CGI Impact Garage Doors Nationwide

CGI Impact Garage Doors: The Dallas Owner’s Guide

We stock, order, and install CGI-compatible impact garage doors and replacement parts across Dallas, with most full door replacements running $3,800 to $8,500 installed depending on size, series, and reinforcement package. If your CGI door has a failed panel, a sagging track, or a spring that gave out, we can usually diagnose it within one visit and get the correct part ordered same week. The call usually starts the same way: the door sounds wrong, it hesitates halfway up, or it simply will not open after a North Texas storm pushed debris into the track. You want the part matched to your exact CGI model the first time, because guesswork with an impact-rated door means a weaker opening than the wall around it.

Call (325) 309-2639

Key Takeaways

• CGI impact garage doors are built to Miami-Dade standards, and every component, down to the track brackets, is part of that rating.
• We are an independent installer in Dallas, not a CGI corporate shop, so our recommendation on OEM versus aftermarket is based on what actually holds up in Texas heat and hail, not a parts catalog.
• Written price before any work starts, and the full repair is covered by our 365-Day Done Right Promise.
• Springs and cables are under extreme tension. Do not touch them without the right tools and training.

Which CGI Models This Applies To

CGI’s impact garage door line splits across a few core series. The most common doors we see in Dallas homes are the CGI 100 Series, the heavier 200 Series, and the Estate Collection, which is where things get specific. A 100 Series door uses a lighter-gauge aluminum rail, typically 2 inches, while the 200 Series and Estate models move to a 2-inch or 3-inch reinforced rail and a heavier end stile. Parts do not always swap between them, even when the panel width matches. The hinge spacing, the roller diameter, and the bracket attachment points all change by series and by the year the door was manufactured.

Every CGI door ships with a factory label on the inside of the top or bottom section, usually on the right side as you face the door from inside the garage. That label lists the series, the model number, and a date code. Photograph it before you call anyone, us included. If the label is painted over or torn, we measure the panel thickness, rail profile, and roller size on site. For OEM parts, series number matters more than anything else. For quality aftermarket, which often runs 30 to 45 percent less than CGI-branded components, we only use equivalents that match the original gauge and fastener spacing. On a door that is supposed to hold a rated opening against wind pressure, a close-enough bracket is not close enough.

Signs Your CGI Impact Garage Doors Is Failing

• The door shudders or shakes on the way up. This usually points to a worn roller or a section hinge that has worked loose over thousands of open cycles. Left alone, the vibration transfers into the track brackets and can pull them out of alignment.
• One side sags when the door is halfway open. The torsion spring is losing tension, or the cable on one side has stretched. On a two-spring CGI setup, one spring can fail while the other still holds, which makes the door look functional while it racks to one side.
• You hear a loud bang from the garage, then the door will not lift. That is a spring letting go. It is the most common failure on any garage door in Dallas, and on impact-rated doors the spring is wound tighter than a standard residential door.
• The door binds or hesitates about three quarters of the way up. The track may have shifted, or the bottom panel corners are worn. We see this after a hot summer where the concrete slab expands and pushes the side jambs slightly inward.
• Daylight or water shows under the bottom seal. The astragal, the rubber strip along the bottom edge, hardens and cracks in Dallas heat. Water intrusion then starts corroding the bottom stile, which on a CGI door is a structural piece, not just a trim piece.

Replacement Cost & What’s Included

Here is the straight pricing for Dallas, based on the jobs we have priced and installed.

• Full CGI impact garage door, single bay, 9×7 or 8×7: $3,800 to $5,600 installed, including new track, springs, hardware, and disposal of the old door.
• Full CGI impact garage door, double bay, 16×7 or 18×7: $5,200 to $8,500 installed, same scope.
• Torsion spring replacement, pair, parts and labor: $380 to $620, depending on spring size and whether it is a one-spring or two-spring conversion.
• Roller and hinge replacement, per section: $90 to $180.
• Track replacement, one side, installed: $240 to $480.
• New bottom astragal seal, installed: $85 to $180.

The range exists because door sizes, wind-load requirements, and existing hardware condition are not the same from one Dallas garage to the next. Before any work starts, you get a written line-item price. That number does not move at the door. The parts come with their manufacturer warranty, and the labor is covered by our 365-Day Done Right Promise, in writing. If the install fails within that year, we come back at no charge, including the second visit.

DIY or Call Us?

For a CGI impact door, the DIY line is short. You can safely check and replace the bottom astragal, tighten visible hinge bolts, and clear debris from the track with the door fully closed and the opener unplugged. Everything else, from springs to cables to track realignment, carries enough risk that I tell homeowners to leave it alone. The torsion spring on an impact-rated door can be wound to the point that a slip can break a hand or worse, and the cables run under enough tension to cut through gloves. This is not a warning to scare you into a call, it is the same thing I tell anyone standing in my own garage. If it involves the spring assembly or any part that holds the door’s weight, call us at (325) 309-2639. We can usually have a technician out to assess the door within the same day, and the price goes on paper before we touch a tool.

One thing I have learned installing doors across DFW, from Deep Ellum lofts to single-family homes in Oak Cliff, is that Texas weather finds weak points fast. A poorly torqued spring sounds fine in March and fails in August. Measure it right the first time, and the rest of the job takes care of itself.

FAQs