New windows and doors improve comfort, cut energy bills and add long-term value to your home. Meridian Windows and Doors Dallas pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
1. Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
2. Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
3. Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
Therma-Tru Window Installation: The Dallas Owner’s Guide
Therma-Tru window installation in Dallas typically runs $450 to $1,100 per window installed, depending on the frame condition, trim work, and whether we’re replacing a window into an existing Therma-Tru door system or setting a brand-new opening. We stock Therma-Tru-compatible window units and hardware on our trucks, and most residential installs are completed the same day. Homeowners usually find us after a window has fogged between the panes, the sash won’t stay up, or water has started pooling on the sill after a Dallas thunderstorm.
A quick note before we get into the details: Meridian Windows and Doors Dallas is an independent service provider. We install and replace Therma-Tru windows and doors, but we’re not a Therma-Tru corporate entity or factory warranty center. What that means for you is straight pricing and one crew accountable for the entire job.
Which Therma-Tru Models This Applies To
Therma-Tru builds window units into several of its door systems, and the compatibility details matter more than most homeowners expect. The Classic-Craft, Fiber-Classic, and Slim-Line entry systems each use window frames sized to the specific door slab, and a window pulled from one line will not seat correctly in another. If you’re looking at the label on the door edge, the last two digits of the Therma-Tru part number tell you the glass type and frame finish, but the series code near the top is what we need to match a replacement.
Here’s the gotcha we see in Dallas regularly: Therma-Tru windows built before 2015 used a different glazing bead profile than current production units. If your home was built in the early 2000s and still has original Therma-Tru entry doors, a factory-fresh replacement window may need a bead adapter. We keep those adapters on the truck because guessing at the job site costs everyone time. For aftermarket equivalents, we only use units that match the Therma-Tru rough opening dimensions within a 1/16 inch and carry the same low-E coating specification. Sloppy dimension matching is why some aftermarket installs look fine for a year and then start leaking at the corners.
Signs Your Therma-Tru Window Installation Is Failing
- Condensation between the glass panes. The insulated glass unit has lost its seal. In Dallas, the swing between 100-degree summers and 30-degree winter mornings accelerates seal failure, and once you see interior fogging, the window’s insulating value is mostly gone.
- Water on the sill after heavy rain. The weep holes at the bottom of the frame are clogged, or the exterior caulk joint has pulled away from the brick or siding. We inspect the full perimeter, because water entering at the top of the frame often pools at the sill before anyone notices the actual entry point.
- The sash will not hold position. On double-hung units, the balance springs inside the track have either worn out or snapped. When one side fails, the window sits crooked and the weather seal on the opposite jamb gets dragged out of alignment.
- Visible daylight through the frame edge. The window was never shimmed correctly during the original installation, and the frame has flexed. In a Texas summer, that gap is also an air-conditioning leak that shows up on your electric bill before you ever see light through it.
- The frame feels soft or spongy to the touch. Water has gotten into the framing lumber around the window. This is the one symptom that turns a simple window swap into a structural repair, and catching it early in Dallas’ humid season is the difference between a $500 job and a multi-thousand-dollar frame rebuild.
Replacement Cost & What’s Included
A single Therma-Tru window replacement in the Dallas area lands between $450 and $1,100 installed for most homes, with the window unit itself accounting for roughly 40 to 60 percent of that figure. The labor portion covers removing the old window without damaging the surrounding trim, inspecting the rough opening for rot or water damage, shimming the new unit square, insulating the frame perimeter, and re-caulking both the interior and exterior with a sealant rated for Texas heat cycles.
Factors that move the price up: second-story access, stucco or brick veneer that requires careful cut-out work, and any frame lumber that needs replacement. What you get from us at every price point is a line-item quote before we touch the window. The price is written down, and it does not change unless we find something hidden inside the wall, which we will show you before proceeding. Every Therma-Tru window installation carries our 365-Day Done Right Promise in writing: if the install fails within a year, we come back and make it right at no charge.
Key Takeaways
- Therma-Tru window installation in Dallas runs $450 to $1,100 per window with us, and most single-window jobs finish same day.
- Window units from different Therma-Tru series are not interchangeable; the series code on the door label is the key identifier.
- Pre-2015 Therma-Tru systems may need a glazing bead adapter for current production units.
- Our 365-Day Done Right Promise covers the installation in writing. If it fails, we return at no cost.
- We carry eight manufacturer lines, including Therma-Tru, PGT, CGI, CWS, and Mr-Glass, so the right product is specced for the job, not whatever is left in the warehouse.
DIY or Call Us?
You can safely check your Therma-Tru window for visible caulk separation, cracked glazing, or moisture trapped between panes. That diagnosis helps us quote the job accurately over the phone. What I’d caution against is pulling the window out yourself. Therma-Tru units are sealed into the slab with structural adhesive and replaceable trim that aligns to the door’s weather seal, and one wrong cut into that assembly turns a straightforward window replacement into a door-system repair. If the window is on a second floor or the frame shows signs of rot, let a crew that carries the right shims, sealants, and level checks handle it. We have the part on the truck, and we’ll have it installed before you finish your afternoon coffee. Call (325) 309-2639 and we’ll give you a straight answer on pricing before anyone rolls a truck.
Frequently Asked Questions
Therma-Tru window units in Dallas generally last 10 to 20 years before the insulated glass seal fails, with the biggest variable being sun exposure. South-facing and west-facing windows, which take the full brunt of the Texas afternoon sun, typically lose their seals years earlier than north-facing units. If your window is fogged, the energy savings from replacement often pays for the window within a few seasons. Call (325) 309-2639 and we’ll give you a replacement price over the phone.
If the frame and sash are intact, we can often replace just the insulated glass unit, which runs less than a full window assembly. If the frame itself has warped or rotted, a complete window replacement is the honest fix. We’ll tell you which one applies to your window after a quick look, and the estimate is free. Call (325) 309-2639 to schedule an inspection.
A single Therma-Tru window replacement in a standard entry door typically takes 2 to 3 hours from setup to final caulk cleanup. Multiple windows or any frame repair add time accordingly. We quote the schedule in the written estimate before the work is authorized, and we show up when we say we will. Call (325) 309-2639 for a timeline on your specific job.
We stock the most common Therma-Tru window sizes and hardware on our trucks, which covers a large share of Dallas homes built in the last 20 years. Unusual sizes or specialty glass types may require a 3 to 10 day order from our distributor. Either way, the price is written down before we begin. Call (325) 309-2639 and we’ll check stock while you’re on the phone.
Get Your Therma-Tru Window Fixed in Dallas
If your Therma-Tru window is fogged, leaking, or won’t stay up, we’ll give you a fixed price to fix it and a written guarantee that the work is done right. Our crew is background-checked and uniformed, the phones are answered by a live person around the clock, and the price you’re quoted is the price on the paperwork. That’s the Garrison Standard, and it’s been how we’ve run this business since the start. Elliot Vance and the team at Meridian Windows and Doors Dallas handle Therma-Tru window installations across Dallas, from East Dallas to Oak Cliff and every neighborhood in between. Measure it right the first time, and the rest of the job takes care of itself. Call (325) 309-2639 today and schedule your free estimate.
Written by Elliot Vance, Owner, Meridian Windows and Doors Dallas at Meridian Windows and Doors Dallas, serving Dallas and nearby areas.
Six Reasons Homeowners Choose Meridian Windows and Doors Dallas
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.